Product ID:TIGTECTIC 21
MSDS Date:09/15/1995
FSC:3439
NIIN:00N088291
MSDS Number: CHLXB

EUTECTIC CORP

1515 BROOK CR
DOWNERS GROVE, IL 60515
US

Emergency Phone: 800-323-4845

Info Phone: 800-323-4845

Cage: 72271

EUTECTIC CORPORATION

DOWNERS GROVE, IL 60515 US

Telephone: 800-323-4845

Cage: 5N977

ALUMINUM (SARA 313)

CAS: 7429-90-5

RTECS: BD0330000

Fraction By Weight: >90%

OSHA PEL 15 MG/M3 DUST

ACGIH TLV: 10 MG/M3 DUST

SILICON

CAS: 7440-21-3

RTECS: VW0400000

OSHA PEL 15 MG/M3 DUST

ACGIH TLV: 10 MG/M3 DUST

AS NOTED ABOVE. REASONABLY EXPECTED CONSTITUENTS OF

RTECS: 9999999ZZ

COATINGS MAY PRDCE FLUORIDE CMPDS, METAL OXIDES,

RTECS: 9999999ZZ

CO, CO*2, NITROGEN OXIDES & CERTAIN INERT GASES USED

RTECS: 9999999ZZ

NICKEL & ITS CMPDS MUST BE CONSIDERED AS CARCINS

RTECS: 9999999ZZ

KNOWLEDGE THEIR ARE NO RELIABLE SCIENTIFIC STUDIES

RTECS: 9999999ZZ

NICKEL RUN INCR RISK OF LUNG CANCER BECAUSE OF EXPOS

RTECS: 9999999ZZ

WAY TO DETERM COMPOSITION & QTY OF FUMES & GASES TO

RTECS: 9999999ZZ

WORKER'S HELMET IF WORN/IN WELDER'S BRTHG ZONE. SEE

RTECS: 9999999ZZ

BOX 351040, MIAMI, FL 33135. FOR MORE COMPLETE

RTECS: 9999999ZZ

(IRON DEPOSITS IN LUNG). METAL FUME FEVER

RTECS: 9999999ZZ

DURING WELDING, HEATING, BRAZING, SOLDERING/CUTTING

RTECS: 9999999ZZ

SICKNESS INCL CHILLS, FEVER, HEAD & MUSCLE ACHE,

RTECS: 9999999ZZ

PAIN, NAUS & VOMIT. SYMPS USUALLY OCCUR W/IN

RTECS: 9999999ZZ

SKIN CONT HAS SHOWN POSS DRYING & MECH

RTECS: 9999999ZZ

CAN PRDCE MILD PULM IRRIT & POSS NONDISABLING

RTECS: 9999999ZZ

SHORT TERM OVEREXP MAY POSE AS

RTECS: 9999999ZZ

CAN CAUSE PNEUMOCONIOSIS OR NON DISABLING FIBROSIS

RTECS: 9999999ZZ

LOCAL POISON CONTROL CENTER. ADVISE OF

RTECS: 9999999ZZ

TRAIN WELDER TO KEEP HIS/HER FACE AWAY FROM FUME OR

RTECS: 9999999ZZ

. WEAR HELMET/USE FACE SHIELD W/APPROP FILTER

RTECS: 9999999ZZ

SHIELD OTHERS. AS RULE, START W/SHADE THAT IS TOO

RTECS: 9999999ZZ

WHICH GIVES SUFFICIENT VIEW OF WELD ZONE.

RTECS: 9999999ZZ

SPKS, & ELEC SHOCK. FOR MORE SPECIFIC

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INHAL: FUMES ASSOC W/HEATING,
WELDING, BRAZING, SOLDERING/CUTTING METALS CAN BE DANGEROUS TO YOUR
HLTH & OVEREXP CAN CAUSE LUNG DMG AND/OR OTHER ORGAN DMG. EYE/SKIN:
ARC RAYS & ULTRAVIOLET LIGH T CAN INJURE EYES & BURN SKIN. ELEC
SHOCK CAN KILL. INGEST: DANGER! MAY BE HARMFUL/FATAL IF SWALLOWED.
(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ: ELEC ARC WELDING, BRAZING,
SOLDERING/THERM SPRAYING MAY CREATE 1/MORE OF FOLLOWING: FUMES,
GASES & DUSTS CAN BE DANGEROUS TO YOUR HLTH. SHORT TERM OVEREXP MAY
RSLT IN DIZZ, NAUS/DRYNESS OR I RRIT OF NOSE, THROAT OR EYES.
EXCESS OVEREXP MAY CAUSE BRONCHIAL ASTHMA, LUNG FIBROSIS,
PNEUMOCONIOSIS/SIDEROSIS(ING 12)
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INHAL OVEREXP: MOVE TO FRESH AIR SOURCE. CONT PHYS & ADVISE
ON INGREDS IN SECTION 2. SKIN CONT: THORO WASH HANDS/EFFECTED AREAS
W/SOAP & WATER TO REMOVE ALL RESIDUE. IF RASH/BURN DEVELOPS,
CONSULT PHY S. EYE CONT: THORO FLUSH W/WATER FOR ATLST 15 MINS TO
REMOVE ALL RESIDUE. OBTAIN PROMPT MED ADVICE FOR FLUXES & CHEM
AIDS. ADVISE PHYS OF INGREDS IN SECTION 2. INGEST: CALL PHYS AND/OR
(ING 20)

Extinguishing Media:CO*2, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . TOXIC FUMES MAY BE PRODUCED. SEE HAZARDOUS
DECOMPOSITION PRODUCTS.
Unusual Fire/Explosion Hazard:GENERALLY NONFLAMMABLE; WELDING ARC,
SPARKS AND FLAMES CAN IGNITE COMBUSTIBLES AND FLAMMABLES. REFER TO
ANSI Z49.1 FOR FIRE PREVENTION DURING USE OF (SUPDAT)

Spill Release Procedures:DISPOSE OF WASTE MATL, POWDERS/FILTER RESIDUES
IN ENVIRONMENTALLY SENSITIVE MANNER I/A/W FEDERAL, STATE & LOCAL
REGS. USE APPROP MEASURES TO KEEP AIRBORNE DUST LEVELS CONTAINED
I/A/W EXPOS LEVELS OF I NGRED SECTION.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:PLEASE READ & UNDERSTAND PRODUCT LABEL
INFORMATION FOR PROPER PROCEDURES AND USE.
Other Precautions:SEE ANSI Z49.1 "SAFETY IN WELDING & CUTTING" &
CHAPTER 11 OF "THERMAL SPRAYING" PUBLISHED BY AMERICAN WELDING
SOCIETY & OSHA PUBLICATION 2206(29 CFR 1910) FOR MORE DETAIL.

Respiratory Protection:IF WORK STATION IS NOT PROPERLY VENTILATED TO
EXHAUST ALL FUMES, VAPORS AND DUSTS BELOW RECOMMENDED EXPOSURE
LIMITS, USE A NIOSH APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GEN VENT & LOC EXHAUST @ WORK SITE TO KEEP ALL
FUMES & DUST FROM WORKER'S BRTHG ZONE & GEN AREA. (ING 21)
Protective Gloves:WELDER'S GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGS (ING 22)
Other Protective Equipment:ANSI APPRVD EYE WASH & DELUGE SHOWER . WEAR
HAND, HEAD, & BODY PROT WHICH HELP PVNT INJURY FROM RADIA, (ING 25)
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZ: WELDING & ALLIED PROCESSES. SOME FLUXES & CHEMICAL AIDS MAY
GIVE OFF HYDROGEN CHLORIDE, PHOSGENE & CHLORINE GASES. CANS UNDER
PRESS & FLAMMS MAY EXPLODE. HAZ DECOMP PRODS: NORM OPERATION IN CL
THOSE ORIGINATING FROM VOLAT RXN/OXIDATION OF MATLS SHOWN IN
INGREDS PLUS THOSE OF BASE METAL & COATING, ETC (ING 3)

Evaporation Rate & Reference:NOT KNOWN
Solubility in Water:NOT KNOWN
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:DUNNG WELDING FUME & GAS DECOMP PRODS
GENERATED ARE DIFFERENT IN PERCENT & FORM FROM INGREDS. DECOMP
PRODS OF (SUPDAT)

Waste Disposal Methods:DISPOSAL MUST BE I/A/W FEDERAL, STATE & LOCAL
REGULATIONS .

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.